How To Store Chainsaw Without Oil Leaking? – 7 Steps

how to store chainsaw without oil leaking

Properly storing a chainsaw is crucial to prevent issues like oil leaks, which can create frustrating messes and damage the saw. As an avid chainsaw user myself, I’ve learned the hard way just how problematic oil leaks can be if chainsaws aren’t stored correctly. In this guide, I’ll share the methods I’ve developed over the years to securely store chainsaws and prevent those annoying oil leaks.

From checking oil levels to using protective cases, I’ll cover all the key steps you need to take. By following these chainsaw storage tips, you can keep your saw in top shape during off-seasons and avoid the headaches of cleaning up oil drips and stains. Let’s dive in!

Checking Oil Reservoirs Before Storage

One of the most important checks before storing any chainsaw is ensuring the oil reservoir isn’t overfilled. Excess oil can easily leak out of the saw during storage, especially as the oil’s viscosity changes with temperature fluctuations.

I like to thoroughly clean the exterior of my chainsaw and then check the oil level window. If the oil level is above the “Full” line, I’ll drain the excess into an appropriate container until it’s at the proper level. Proper oil level maintenance prevents leaks and also optimizes the saw’s performance.

If you’re storing a chainsaw for an extended period, it’s also wise to drain the oil reservoir completely. Over several months, even oil at the correct level can leak out of small openings. Emptying the reservoir prevents this. Don’t forget to refill it with fresh, high-quality bar and chain oil before using the saw again.

Replacing Worn Out Plugs Before Storage

Another culprit that can lead to oil leaks is worn out rubber plugs around chainsaw oil ports. Over time, these plugs lose their elasticity and can’t maintain a tight seal. Before storage, carefully check each plug on your saw. Look for any cracking, dried out or flattened plugs.

If any plugs look compromised, replace them immediately. It’s a quick fix that only requires inexpensive replacement plugs. New, supple plugs will seal tightly to prevent leaks during storage. Allowing worn out plugs to remain is asking for problems down the road. An ounce of prevention is worth a pound of cure when it comes to leaky chainsaws!

How To Store Chainsaw Without Oil Leaking? - 7 Steps

Storing Saws in Protective Cases

Rather than leaving a chainsaw loosely on a shelf or workbench, I strongly recommend storing it inside a protective case. High-quality cases are designed specifically to prevent oil leaks and damage during storage.

Look for cases with a shape that securely holds the saw in place. Padding inside the case absorbs impact if the case is dropped. And water-resistant exteriors prevent moisture damage which can loosen oil plugs over time.

A quick online search will reveal lots of suitable chainsaw cases. Look for brands designed for your specific saw’s make and model for the best fit. Yes, cases represent an additional investment but it’s worthwhile. Preventing just one oil leak will offset the cost of a case many times over.

Inspecting and Cleaning Saw Bodies Before Storage

Before packing up a chainsaw for storage, it’s wise to inspect the saw’s inner workings and clean any oil residue or debris. Buildup inside the body can lead to clogged oil lines or other issues.

I like to use pressurized air to blow out any dust and dirt inside my saws before storage. An old toothbrush also helps scrub stubborn gunk away. Make sure any oil accumulation inside the body is cleaned away as well. A sports water bottle with a squirt nozzle is great for blasting away oily residue.

Thorough cleaning leaves less residue to potentially block oil lines or drip out during storage. It also allows me to inspect the saw’s inner workings for any issues needing repair before the off-season. An hour spent cleaning and inspecting now saves hassle when I pull the saw out months later.

Storing Chainsaws Vertically to Avoid Leaks

Oil leaks frequently occur when chainsaws are placed horizontally for storage. The various openings in a saw’s housing become pathways for oil to drip out when sideways or upside down.

Simply storing a chainsaw vertically prevents this issue. The oil stays securely in the reservoir instead of leaking out openings in the clutch cover, chain brake, or bar tip.

I use sturdy mounted brackets to store my saws vertically along my garage wall. The saws stay securely upright and ready for quick access when needed. Vertical storage should become a habit for any chainsaw owner. It solves so many preventable oil leak issues.

Keeping Saws in Cool, Dry Locations

Temperature and humidity are often overlooked factors when storing chainsaws but they make a big difference. As temperatures rise, oil becomes thinner and flows more freely through tiny openings. Storing saws in hot sheds or garages promotes leaks.

Instead, keep saws in the coolest location possible during storage. For most homeowners, that means a basement or air-conditioned interior room. Cold temperatures cause the oil to thicken and reduce leakage.

Low humidity also discourages leaks. Damp storage conditions can cause metal surfaces to oxidize and rubber oil plugs to degrade. A dry environment keeps everything sealed up tight. Make sure your storage location addresses both temperature and humidity considerations.

Signs Your Chainsaw Oiler Is Working Correctly

Since oil leaks and oiling issues are common chainsaw problems, it’s wise to periodically verify that your saw’s oiler is functioning properly before storage. Here are some quick checks:

With the chainsaw stopped and bar removed, start the saw and observe oil discharge from the oiler orifice. A steady stream of oil indicates things are working. No discharge means a clog or pump issue.

Also watch oil flow with the bar attached. Turn the tip upward and give the trigger a blip. Oil should flow along the bar in a steady stream. Inconsistent oiling can be fixed with oiler adjustments or a good bar cleaning.

Taking a minute to confirm oil flows correctly before storage gives peace of mind. And preventing oil system issues now prevents bigger headaches when you go to use your saw again later.

Adjusting Oiler Settings and Inspecting Oil Lines

Along with the larger steps already discussed, a few smaller maintenance tips will further ensure oil leakage is avoided during chainsaw storage:

  • Carefully adjust the oiler mechanism to deliver adequate but not excessive oil flow. Over-oiling leads to leaks and waste. Consult your operator’s manual for the proper adjusting procedure.
  • Inspect all oil lines for cracks or defects. Look closely at areas where lines meet metal fittings. Replace any damaged sections – don’t just patch small leaks.
  • Keep the oil tank cap and outlet vents clear of debris that could block ventilation. Proper air circulation prevents pressure buildup.
  • After each use, clean the guide bar rails and sprocket of wood chips and dirt that impede oil flow. A clean bar oils efficiently.

By being diligent with preventative maintenance, you can have full confidence your saw will store securely without any oil drips or stains. It takes a modest time investment but the payoff is worth it.

Can I Use the Same Steps to Remove a Stump with a Chainsaw and Store the Chainsaw without Oil Leaking?

When it comes to removing a stump with a chainsaw, following the same steps is not necessary for storing the chainsaw without oil leaking. While the process of removing the stump requires proper techniques and safety precautions, storing the chainsaw without oil leaks generally involves cleaning the equipment, emptying the oil tank, and ensuring proper storage conditions.

Key Takeaways for Leak-Free Chainsaw Storage

To summarize, leakage-free chainsaw storage requires attention in these key areas:

  • Checking and adjusting oil levels in the reservoir
  • Replacing worn out rubber plugs around oil ports
  • Using a protective storage case designed for your saw
  • Thoroughly cleaning all oil residue and debris prior to storage
  • Storing the saw vertically to keep oil in the reservoir
  • Selecting a cool, dry storage location to avoid leaks
  • Inspecting the oil delivery system for defects and proper function
  • Making small adjustments and performing maintenance as needed

Following these essential tips, you can look forward to leak-free, trouble-free chainsaw storage. No more oil stains and exasperating issues when you go to use your saw again. Invest a little attention upfront and you’ll reap rewards with a high-performance saw ready for action when you need it.

Frequently Asked Chainsaw Storage Questions

How often should I clean my chainsaw?

It’s wise to do a quick cleaning after each use to remove sawdust, sap and dirt. A more thorough cleaning every 10 hours of runtime helps keep your saw in peak shape. Clean any leaks or oil residue before storage.

What type of oil should I use for my chainsaw?

Use a high-quality bar and chain oil designed specifically for chainsaws. Look for brands that say “tackiness additive” to help oil stick to the bar and chain. Never use old motor oil!

How do I know if my chainsaw needs a new oil pump?

If oil isn’t flowing properly and you’ve checked for clogs, test the pump output with the bar removed. If oil discharge is weak, intermittent or non-existent, have your dealer test the pump and repair if needed.

Can I use a different brand of oil in my chainsaw?

It’s fine to use a different brand as long as it meets your saw’s oil specifications. Avoid vegetable or bio-based oils. Look for tackiness additives and anti-gelling agents for your climate.

How do I adjust the oil flow on my chainsaw?

Consult your owner’s manual for model-specific steps. Typically, a simple screw adjustment on the pump varies oil output. Increase flow if the bar and chain show dryness; decrease if excess oil flung off the chain.

What are signs of a chainsaw oil leak?

Oil drips under the saw, loss of oil in the reservoir, oil stains in the carrying case, and oil dripping from the bar tip while stored upright can all indicate a leak.

How can I prevent my chainsaw from leaking oil during use?

Proper oil reservoir filling, sealing old or damaged oil lines, cleaning the bar oil hole regularly, and not over-oiling are key steps to reduce leakage when sawing. Adjust flow rate to your task.

Properly caring for and storing your chainsaw will pay dividends down the road in reliability, performance and lack of frustration over oil leaks. Follow this guide and you can look forward to leak-free operation for years to come. Here’s to a cleaner saw and work area!

Similar Posts