How to Keep a Chainsaw from Pinching? – Easy Ways

how to keep chainsaw from pinching

One of the most dangerous potential problems is ‘pinching’, which occurs when the blade catches on something as it cuts through wood or other material. This can cause serious injury to the user or others nearby, and result in costly damage to the saw or other property. Fortunately, there are some simple and easy ways that you can keep your chainsaw from pinching. By following these steps, you can drastically reduce the risk of a dangerous incident occurring while using your chainsaw.

You need to ensure that you have the right type of blade for the job. Different materials require different types of blades; make sure to select one appropriate for what you’re cutting through at any given time. This will minimise the chance of pinching as well as maximise the efficiency of your sawing task. Also, here is a complete guide to How to keep a chainsaw from Pinching in Simple and easy ways.

How to Keep a Chainsaw from Pinching?

how to keep chainsaw from pinching

Chainsaws can be dangerous if used improperly and one common problem is known as “pinching” which can cause the blade to become stuck in the material it is cutting. 

To reduce the risk of pinching while using your chainsaw, there are a few steps you should follow:

Pre-Cutting Preparation

Wear proper safety gear, including a face shield, gloves, and chaps. Also, make sure the chainsaw is in good working condition with a sharpened chain and properly tensioned bar. Now clear branches from around the cutting area and inspect for obstructions before starting the saw.

During The Cut

Avoid pinching by keeping the body of the saw above the guide bar when cutting. Don’t force the saw in an unnatural direction or push too hard on it during use as this can cause binding and kickback. Also, Maintain a steady speed, especially when making deep cuts to keep from overloading the chain.

See also  Do You Need a License to Use a Chainsaw in 2024?

After The Cut

Disconnect from the power source and wait for it to stop moving before setting it down. Now Check the surrounding area for debris or foreign objects that may have become wedged in the bar or chain. At last Clean and lubricate with appropriate oil as needed after each use.

How Do You Cut a Log Without Pinching It?

Cutting logs without pinching them can be accomplished using a variety of tools. For smaller logs, such as those used in firewood, a hand saw is often the best choice. It’s important to make sure that you use an appropriate size saw blade, in order to reduce the risk of pinching. When cutting longer or larger pieces of timber, a chainsaw or circular saw may be more suitable. 

The key is to steady the log with one hand while operating the cutting tool with the other. To ensure that your hands are not in danger of being pinched by the blade, keep your fingers away from the teeth and wear protective gloves if necessary. Additionally, some specialised saws are available which feature anti-pinching technology.

Selecting the Right Saw

Select the right saw for cutting a log. Chainsaws are usually used for larger logs and circular saws or reciprocating saws work well for smaller logs.

Set Up Your Log

Place your log on a flat, level surface and secure it with clamps to prevent rolling while you’re working. If you don’t have clamps, use wedge pieces of wood to keep the log steady.

Start Cutting

Make sure that your blade is sharp before you begin and wear protective gear such as gloves, goggles, and hearing protection. Get in a comfortable position and use slow, steady strokes to guide the saw.

Avoid Pinching

Keep your hands away from the blade and use a jig if necessary to help keep you in alignment with the log. If you feel the saw starting to pinch, stop and reposition it before continuing.

Finish Up

Once you have finished cutting through the log, stop the saw immediately and turn off its power switch. Allow it to cool down before handling it again or storing it away. Clean up any debris around the work area and discard both of logs safely.

How To Cut a Tree Without Chainsaw Pinching?

Cutting down a tree without chainsaw pinching is possible, although it takes some extra effort and skill. The most important thing to remember is to plan ahead. Consider the size of the tree, its location and any obstructions nearby that could be a problem when cutting it down.

See also  How to Tell if Chainsaw is Dull? - 2024 Guide

If you are using an axe or saw, make sure the blade is sharp and in good shape. This will help to ensure a clean cut with no pinching when cutting down the tree. You should also use an appropriate safety harness and hard hat when working on a tree, especially if you are not experienced with cutting trees. Here are some steps on How to cut a tree without chainsaw Pinching?

Preparing Your Tools

Before you begin, make sure that you have the right tools to safely cut down a tree without using a chainsaw. You will need an axe or saw (preferably with a longer blade than usual), safety goggles, and gloves. Make sure that your tool is sharp enough to easily penetrate into the trunk of the tree.

Identifying The Right Spot To Cut

To accurately and safely cut down a tree without using a chainsaw, it is important to identify where the tree should be cut from. This spot should be at least one-third of the way up from the base of the trunk. Look for any weak spots on the bark or signs of disease that may indicate rotting. These spots will make it easier to cut into the tree.

Making The Cut

Once you have identified where to cut, use your axe or saw and start making a downward incision in the bark on the opposite side of where you are standing. Make sure that your cuts are deep enough to penetrate through more than one-third of the trunk’s circumference. Move back and forth until a notch is made around the entire circumference of the trunk. This notch should be wider than two inches at its deepest point. 

Pinching The Tree To Finish The Cut

After you have finished cutting all the way around with your axe or saw, get ready for pinch cutting! Start by finding a wedge (such as a log or stone) that is close in size to the notch made around the tree. Place it into the notch created and use your weight to press down with both hands on either side of the wedge. This will help pinch the trunk at its weakest point, causing it to lean in the direction of where you want the tree to fall. Once it begins to tilt, step away and let gravity do its job!

Final Tips

When cutting a tree without using a chainsaw, make sure that you are wearing appropriate safety gear (gloves, goggles, etc.) and have identified any weak spots on the tree prior to starting.

What To Do If Your Chainsaw Gets Stuck in a Tree or Log?

If your chainsaw gets stuck in a tree or log, the first thing you should do is turn off the engine and remove the spark plug wire. This will help to prevent an accidental start up of the saw. Next, check the chain tension on your saw; if it is too tight, loosen it slightly. If possible, apply heat to the bar with a propane torch for about 2 minutes; this can help to loosen any resin or sap that may be holding the saw in place. 

See also  What is an Arborist Chainsaw? A Comprehensive Guide

Using a rubber mallet or hammer and block of wood (or similar material), gently tap around the circumference of the blade until it starts to move freely again. If necessary, use a wedge to help pry out the blade. 

Conclusion

Keeping a chainsaw from pinching is not a difficult task. By following the simple steps outlined in this article, you can ensure that your chainsaw will run smoothly and safely. Be sure to always check the chain tension before use and keep sharpening the chain regularly for optimal performance. Finally, take proper safety precautions at all times when operating any power tool or machinery. With these helpful tips, you are now well-equipped to maintain your chainsaw properly and avoid pinch points! 

FAQs

Q: What is a chainsaw pinch?

A: A chain saw pinch refers to the force exerted on the saw when it binds up due to dull or dry wood, impacting the ability of the bar and chain to move freely. This can cause serious injury if not addressed immediately.

Q: How can I prevent a chainsaw from pinching?

A: To prevent a chainsaw from pinching, ensure that your chainsaw’s chain is kept sharp and lubricated at all times. Also, make sure you are using a suitable guide bar for the job. It should be just long enough to cut through whatever material you’re cutting.

Q: Are there any techniques I can use to prevent a chainsaw from pinching?

A: Yes, there are several techniques you can employ to help prevent a chainsaw from pinching. When cutting into thick wood, make sure to take your time and cut with the grain instead of against it. Additionally, you should always use two hands when cutting, as this will give you more control over the saw.

Q: What should I do if my chainsaw starts to pinch?

A: If your chainsaw begins to pinch while in use, turn off the engine immediately and check the chain for damage or clogging. Clean out any debris that may be obstructing its movement. Then sharpen or replace the chain as necessary and make sure it is properly lubricated before starting up the engine again.

Q: Can I use a chainsaw on dry wood?

A: While it is possible to use a chainsaw on dry wood, this can increase the chances of it pinching due to the lack of lubrication present in the wood. Therefore, it’s best to avoid using a chainsaw on dry wood altogether. Instead, use a hand saw or other cutting tool that won’t bind up as easily.

Similar Posts